Method

So I was a little nervous about my clone-a-pussy experience. I'd read several reviews that documented failed attempts and carefully noted what to do to avoid these problems. Here is what I did to successfully clone my pussy:

1. Gather all materials. Everything in the kit plus a paper cup and 2/3 cup hot water (I let mine cool to lukewarm from hot) and a mixing bowl for the molding material. Also useful are a clock for timing, some newspapers to lay on the ground and a shower to jump into afterwards.

2. Before you mix the molding powder and water, make a game plan. Where are you going to sit or squat for 4 minutes while the mold is hardening? It's best to have the molding cup parallel to the floor. I ended up straddling a small desk I have and using my hand to keep the mold in place. Lay down some newspapers to catch spillage, because this will very likely spill. Another thing to consider is if you want your pussy molded with lips parted or sealed shut. Check yourself out in the mirror and see what kind of pose you want your pussy in and what kind of stretching of the skin needs to happen for that position to take. Practice getting into position with the cup while holding your pussy how you'd like it. Remember: you don't really want to mold your fingers (unless you do?) so keep them out of the cup.

3. When mentally and physically prepared, the water having reached lukewarm, pour the water and molding powder together in the bowl and stir quickly and thoroughly with the provided stir stick. In the instructions it says that you have a minute to do this, but reading other peoples' experiences I learned that it can set faster than that and botch your molding experience. I just stirred it as quickly as possible until it was all combined then used my extra few seconds to get the molding cup and my pussy into position. The reason you want the water at lukewarm temperature is because you will be dipping your lady bits into it. Just think of that when you're testing your water.

4. And hold. Wait 4 minutes. I found it didn't take quite that long for the mold to set. I got a clue because some of the spilled molding material had stiffened. When you're sure the mold has set, remove thyself from it.

5. OK, now moving on to the filling part of the molding process. There are two jars that come in the kit, one of rubber and one of "Liquid Skin." Open both of these and empty the contents completely into the paper cup. Use the other end of the stir stick to scrape every last bit of material into the cup then use it to stir. Stir vigorously for 2 minutes. It's going to smell a bit so you might want a window open. After the time is up, just pour carefully into your mold. Then give the mold a few good gentle taps on the table and vibrations to release air bubbles and ensure that all the little crevices are filled.

6. Let your creation sit for at least 24 hours on a level surface.

7. After your time is up, step on up and carefully peel your clone from it's little nest. The rubber can tear so have a gentle touch when you do this. Any strange extra bits from the molding process can be trimmed off. Did it work? Let us know! Hopefully more people can do this with success!

Material Info

Materials info was a little tricky to track down. There is virtually no information about the materials used in this kit on the kit itself or on the Empire Labs website. They do inform us that the clone we end up making is rubber and that there is no latex in this product. But I want to know what the molding material is. From doing my own research I believe it is an alginate of some sort. Alginates are derived from seaweed and they are used for live casting (that's what making a mold of your pussy or arm or face is called). Molds made of this material are not terribly strong and if left out in the air they can dry up completely. (Source) This material sounds the closest to what is in this kit, because it is advised to store the mold submerged in water if you want to keep it for future use.

(continued...)

Of course if you do intend to go on and make an army of cloned pussies, all power to you! I would suggest doing some more in depth materials research if that is your plan. Particularly I suspect that you want to mix and pour rubber in a well ventilated area, though I have not verified that.

Tint-wise you do end up with a light caramel coloured pussy clone. There is a deeper tone clone a pussy as well as a chocolate molding kit, but those are not currently carried on Eden Fantasys. Here we have a much wider selection of options for "willy cloning."

Notes & Experience

After I'd removed myself from the mold I was sure that I was sunk. Honestly it looks so weird when you see your pussy in negative. I had these weird cracks running really far into my mold that I thought were mistakes until I realized that my lips actually extend quite far out. It was so surprising to see the mold that was made!

Fortunately my fears were for naught, because when I peeled my rubber pussy out it looked really damn good. It's not 100% perfect. There are a couple little bumps up near my clit that make it look like I have some kind of genital warts, but really that's only upon close inspection. Overall for my first time doing this it looks great. The mold really picked up the texture of my skin especially on my inner labia. You can even see my clit because I was holding myself somewhat split beaver.

Speaking of labia lips, if you have very very long labia lips you might have some issues with them pressing into the bottom of the molding cup. I have long labia. Nothing extreme, but they did touch the bottom of the cup at one point leaving a little flat spot on the edge of my mold. Then again I was pressing myself pretty deep into the cup.

I did this venture solo, but it would be a bit easier with a partner or friend to help. They could stir the materials and help with any positioning or spillage. Plus it would be a bonding experience, for sure. Just be sure to keep in mind how silly the whole situation is and not take it too seriously!

Overall I enjoyed this experience. The 24 hour wait time feels a lot like back in the old days when you had to actually wait to get your photos developed. I like that element of mystery and the surprise that comes from seeing the end result.

Clearly this is a novelty item, so it doesn't have immense lasting power. My cunt casting still looks beautiful though. I've stored my mold in water as instructed and it still looks usable though the water it's in is getting a bit cloudy.