Cloned Bone
If you want to have some fun as a couple making a mold of the male half, then give it a try. Just don't expect it to be perfect, and be ready to have a ton to clean up.
Published:
Pros
Easy to read instructions, Couples fun
Cons
Messy
We made our clone-a-willy last night and it was definitely an experience we won't forget! The kit included thermometer, molding tube, molding powder, liquid rubber #1, liquid rubber #2, vibrating unit (ours was purple) and the directions. You will need to provide water, liquid measuring cup, mixing bowl (I would recommend using a bowl that you can simply throw away; we used a country crock butter plastic tub), scissors, tape, timer and cardboard. Be sure to have an area cleaned off and put some newspaper down where you are standing, because this will get messy. To do this kit there are some basic steps outlined in the directions but there is definitely more to it than just the basic instructions imply. The male half needs to shave or at least trim the area before hand. Trust me on this one; peeling mold out of pubic hair is not fun. Next, gather everything up and sort it by when it's needed. Then read the directions, and then reread them once more.
The first step is to cut the tube to fit. Make sure to give yourself an extra inch. The next step was to mix the material with water (the water has to be exactly a certain temperature) and start the timer. My advice is to wear a cock ring, because while trying to maintain an erection under the pressure of having two minutes to mix and insert can be a challenge. Remember, you only have one shot.
Next step is to insert your unit into the tube. Remember when you had chicken pox when you were little and had an oatmeal bath? It felt like putting your unit into that. Then you have to hold that position until it fully gels. If you go limp, don't worry it's usually almost gelled by the time you insert. Then you have to let it sit for 2-6 hours. Check on it every half hour or so, and pour any water you get out.
The third and final step is to mix the actual silicone and pour. You may want a fan on during the pouring phase because this stuff smells like a horrible chemical epoxy. After it is poured, you take a small section of cardboard and cut a hole through it. Then you insert the vibrator into that and place it in the mixture. This will displace some sticky goo, so be careful. Wait 24 hours then pull the mold out. Congratulations, you made a willy!
The first step is to cut the tube to fit. Make sure to give yourself an extra inch. The next step was to mix the material with water (the water has to be exactly a certain temperature) and start the timer. My advice is to wear a cock ring, because while trying to maintain an erection under the pressure of having two minutes to mix and insert can be a challenge. Remember, you only have one shot.
Next step is to insert your unit into the tube. Remember when you had chicken pox when you were little and had an oatmeal bath? It felt like putting your unit into that. Then you have to hold that position until it fully gels. If you go limp, don't worry it's usually almost gelled by the time you insert. Then you have to let it sit for 2-6 hours. Check on it every half hour or so, and pour any water you get out.
The third and final step is to mix the actual silicone and pour. You may want a fan on during the pouring phase because this stuff smells like a horrible chemical epoxy. After it is poured, you take a small section of cardboard and cut a hole through it. Then you insert the vibrator into that and place it in the mixture. This will displace some sticky goo, so be careful. Wait 24 hours then pull the mold out. Congratulations, you made a willy!
Experience
Ours came out like an inch and a half to two inches small, because even with a cock ring I had problems concentrating on the activity and started going soft. In the end, everything is visible from veins to hair. As far as use as a sex toy? The cloned unit was almost too solid to be a rubber vibrator, and had some problems with random hard spots. Maybe if the material was a little more flexible and less rigid, then it would be used more. It was a fun experience and it could make a great conversation piece.
Final product:
Final product:
Follow-up commentary
4 months after original review
Every time I look at the cloned piece it makes me sad. It had the possibility of being such an amazing product but with such disappointing results. If you have spare money to throw around, give it a whirl but don't expect too much and just be prepared for the depression that comes along with a failed kit.
This product was provided at a discounted price in exchange for an unbiased review. This review is in compliance with the
FTC guidelines.
EdenFantasys Review Program
- Get Free Toys
- Enjoy Special Deals
Comments
Subscribe to comments
-
I'm sorry this didn't work out to well, thanks for the review!
-
Great review
-
Nice review thankyou
-
Great review!
-
thanks for the review
-
Neat!
-
Thanks!
-
Great review. Thanks!
-
Thank you
-
Wow that is detailed. I think I might just buy this for the fun of making it.
-
thanks for the review
-
thank you for the review!
-
Thanks for the review!
-
Thanks for a good, helpful review.
-
thanks
-
thanks
-
thank you for the photo! great review! sorry you're so disappointed.
-
Thanks!
Forum
Discussion | Posts | Last Update |
---|---|---|
#AskEden - Clone-A-Willy in other colors? | 9 | |
Did you have complications with this kit? | 5 | |
Any Clone-A-Willy products that use a better material? | 9 | |
Have you Cloned-A-Willy? | 21 | |
clone a willy | 17 | |
material safety and cleaning? | 3 | |
Clone-a-willy construction! | 27 | |
Curious | 4 |
- See all discussions
Thank you for viewing Clone-a-willy kit – secret dildo review page!