The kit includes ALMOST everything you need. You will want to pick up a cock ring, and have a piece of cardboard, scissors, and two disposable containers for mixing the products in.

When you are ready to start the process, be sure you have read ALL of the instructions, and I suggest more than once. A lot of the steps require precision, so if you had misread something, you may end up doing something wrong and ruining the entire project. Have all of the materials sitting out beforehand, this way everything is ready to go when you need it.

The first thing you do is cut the tube that the materials came in to the length of your man's erect penis. This is simple, as you just place the tube next to his penis, and mark the length on the tube, and then cut. He will need to stay erect during the process, so a cock ring (which is not included) is HIGHLY suggested.

After the cut has been made, you will need to take the thermometer, run the tap water until you reach EXACTLY 98 degrees. This can be done by keeping the thermometer under the running water and adjusting the taps. This was not that hard to do, but it takes a bit of adjusting while your man is just standing there, keeping it erect.

Once you have the water temperature you need, you will need to measure out the required amount, pour it into a disposable container, and then pour a mixture into this water. Once you have done this, you have exactly two minutes to do the rest of the required actions, or else it will be ruined. That in and of itself was a bit stressful to me because we paid for the item, and if it was ruined, we just threw our money down the drain. Luckily though, I am a perfectionist.

So, at the start of the two minutes, you are required to mix the contents in the container for one minute. That leaves you with one more minute. In this minute, you need to pour ALL of the contents into the tube that you cut earlier, ensure your man is at his peak of erection, and then have him stick his erect penis into the tube. He needs to keep his erect penis in the tube for two whole minutes. He also needs to try and not have his penis touch the sides of the tube.

The picture on the directions has a man standing up, holding the tube on his erection. So I had my boyfriend stand up, and slide his erect penis into the tube. I am not sure why the man on the picture looks so tidy, considering this was a very messy step. When your man sticks his penis in the tube, the mixture WILL come out. Be sure to do this over some newspapers or a tiled floor so that you can clean it up. Luckily we did not do it on our carpet as I am not sure if it would have come out.

Okay, so after the two minutes is up, he can take his penis out of the tube. You now need to wait two hours before continuing the next steps so the mould can set. This leaves you with time to show your appreciation for all your man's hard work, or to clean up the big mess you both have created with this project.

One important thing I need to mention is that I had my man shave before we started this. I didn't want hairs stuck in the mould, or his hairs ripping out. I suggest trimming right down, or shaving completely before embarking on this journey.

Once the two hours have passed, you combine the rest of the mixtures together, and pour them into the tube which now has a mould of your man's penis. You will need to then cut an "X" into a piece of cardboard, place the vibrator through the X and place the piece of cardboard on top of the tube, allowing the vibrator to sit inside the tube. Be sure to have the bottom of the vibrator sticking out of the cardboard so that you are able to replace the batteries when they die.

Once this is done, you will need to let it sit for 24 hours so that the mould sets. Once the time is up, you cut the tube open, and carefully take your man's replica penis out of the mould and voila! It's certainly a project that needs to be done with precision, but if you do it right, it's well worth the money!

I decided to buy this item because of its uniqueness. I mentioned it to my man and he was flattered that I wanted his penis for when he wasn't around. I think most men would be flattered with this idea.

I mentioned above that it was a bit stressful following the exact measurements, exact temperatures, and all with time constraints. Though it was stressful, it was a unique experience I will never forget. It was our first time using a cloning product, and it turned out perfectly.

My partner and I had so many laughs during the process, especially when he had to put his erect penis into the tube containing the mixture. The mixture spewed out the sides, all on to the floor and down his legs. Also, once the two minutes were up, he said out loud to me, "Um, I think my penis is stuck". We roared with laughter. His penis was not stuck, he was just afraid to ruin the mould so he wasn't pulling it out hard enough.

Before starting the project, I thought it might be fun and sexy. It was fun, but the process was far from sexy. Expect a bit of stress, and a lot of laughs.

As for the experience with the product once it was complete, I find the vibrator to be very weak. There is only an on and off button. If you are like me, you enjoy variations of vibration speed...don't expect that from this product.

The finished product is also really amazing in detail. You can see every vein, and any little detail that is on your man's penis. It is extraordinary! Even my man was impressed when he saw the final product. We also both really liked the fact that it glows in the dark. We kept it by the light for a minute or two, we turned the lights off, and saw his glowing penis. We then laughed some more.

I would definitely try another clone-a-willy product because ours had turned out so well. The only reason I gave it a 4 out of 5 stars and not a 5 out of 5 is because it is a bit stressful and requires the user to follow the directions exactly. There is NO room for error.

Also, if you do use the clone-a-willy for insertion once the product is finished, be sure to use a condom as the material safety of the product is a 3 because it is rubber.

I still love my man's cloned "willy", but I don't use it as often for solo play any more now that I have a rabbit vibe. I still love it though, and it's still running on the same batteries I put in it. The fact that it only has one vibration setting though really sucks. When my partner and I are together, that is when the clone-a-willy is used most now.